Recent comments in /f/DIY
Trolleitor t1_j0zat0h wrote
Reply to I made a honeycomb firewood rack by richriggins
Pathetic wood hexagon stick holder vs proper metal wood storage
Looks rad man
Browneyedgirl63 t1_j0zalvx wrote
Reply to comment by richriggins in I made a honeycomb firewood rack by richriggins
It’s great how you can just keep adding and adding. And it looks nice and neat.
richriggins OP t1_j0z9z0y wrote
Reply to comment by Tableau in I made a honeycomb firewood rack by richriggins
Notice how in the picture where it's full of wood you can't see those welds?
Tableau t1_j0z9ljc wrote
Reply to I made a honeycomb firewood rack by richriggins
Looks good, but if you wire brush that flux off it would look a little nicer
Tableau t1_j0z98m4 wrote
Reply to comment by richriggins in I made a honeycomb firewood rack by richriggins
Angle grinder
Tableau t1_j0z8rdt wrote
Reply to comment by c1e2477816dee6b5c882 in I made a honeycomb firewood rack by richriggins
If you buy it at the hardware store. They mark that shit up crazy high. If you go to an actual metal supplier it’s much more reasonable
[deleted] t1_j0z7hpg wrote
Reply to comment by [deleted] in I made a honeycomb firewood rack by richriggins
[removed]
Jeffusion t1_j0z6ltd wrote
Reply to comment by believe2000 in I made a honeycomb firewood rack by richriggins
Thank you for your service. I came looking for this.
cigarking t1_j0z6dga wrote
Reply to comment by richriggins in I made a honeycomb firewood rack by richriggins
Lol.
[deleted] t1_j0z5m7p wrote
Reply to comment by [deleted] in I made a honeycomb firewood rack by richriggins
[removed]
richriggins OP t1_j0z5k3z wrote
Reply to comment by Browneyedgirl63 in I made a honeycomb firewood rack by richriggins
Yeah, calling my steel folks tomorrow to place a material order for 3 more...
richriggins OP t1_j0z5axt wrote
Reply to comment by drfarren in I made a honeycomb firewood rack by richriggins
Damn...
[deleted] t1_j0z54od wrote
Reply to I made a honeycomb firewood rack by richriggins
[removed]
richriggins OP t1_j0z5474 wrote
Reply to comment by Valalvax in I made a honeycomb firewood rack by richriggins
Not quite, the switch changes the orientation of the magnets, not the distance.
Browneyedgirl63 t1_j0z51kt wrote
Reply to I made a honeycomb firewood rack by richriggins
You did a great job. Looks like you might need more.
TotalWalrus t1_j0z4bmq wrote
Reply to comment by richriggins in I made a honeycomb firewood rack by richriggins
Oil the seams. itll help slow the rust
se69xy t1_j0z43at wrote
Reply to I made a honeycomb firewood rack by richriggins
The metal looks better than the wood…well done.
YearningInModernAge t1_j0z42sy wrote
Reply to comment by SwampyJesus76 in Expired Caulk setting slowly by [deleted]
Thank you, and will do
YourPlot t1_j0z3xyh wrote
Reply to I made a honeycomb firewood rack by richriggins
This looks way better than my flimsy Amazon purchased wood rack. I wonder if I should pick up welding…
[deleted] t1_j0z3x8l wrote
Reply to comment by Frost_999 in I made a honeycomb firewood rack by richriggins
[deleted]
PanZlty t1_j0z3umk wrote
Reply to I made a honeycomb firewood rack by richriggins
JFYI the actual inside walls of the honeycomb are round not hexagonal.
[deleted] t1_j0z3tco wrote
Reply to comment by N_Inquisitive in I made a honeycomb firewood rack by richriggins
[deleted]
SwampyJesus76 t1_j0z2y3s wrote
Reply to Expired Caulk setting slowly by [deleted]
Caulk is good for a year tops, toss it and redo.
Valalvax t1_j0z2xi8 wrote
Reply to I made a honeycomb firewood rack by richriggins
Disappointed that you never mentioned the final price... My guess is about 140 for the welder, 50 for the fan, and 200 or so for the metal, but just spit balling with basically no reference except for the welder
(I actually assume that fan cost about the same as the welder, but decided to low-ball my guess)
Tableau t1_j0zbpbh wrote
Reply to comment by richriggins in I made a honeycomb firewood rack by richriggins
I do, but it takes literal second to do